Polyester spinning machine is a textile machine specifically used to textile polyester wire, so it is essential to ensure product quality, which is essential for maintenance and maintenance.

1, often check the polyester spinning machine

Check whether the sound of the drive head and the transmission space in the tail transmission is normal; whether the sync tape is shifted; the bearings at each roller component, friction roller member, and the drive member, etc. are heated and vibrated; whether the leather roll is scarned; Fake twisters and cartridge clips and the flexible rotation of the leather rolls are flexible.

2, regularly repair polyester spinning machine

Small repair is generally based on cleaning equipment, and checks the damage of each of the operating parts and the guide. The overhaul is in addition to the inspection cleaning, the cleaning and wear of the synchronous belt, the synchronous pulley; opening the groove Wear conditions such as cartridges, shuttle, slider, and the like. Overhaul cycle: car repair once every 2-5 weeks, 1-3 months.

3, heat box maintenance

Since the spline is tube tube, the spinning oil on the filament is heated and volatilized, and the component with a small portion of the boiling point remains in the heat pipe, and the resulting fourth bonding can affect the heating effect of the wire. , Causing the quality of DTY to decline, so you should clear it regularly. The cleaning cycle depends on the fiber of the processing filament, the speed of the machine and the type and content of the POY oil, generally 2-3 months. Regularly clean the guide wire tube in the hot tank. Pumped from above, immersed in 15% -20% alkali solution and heated, after cooling, washed out, washed with hot water, and then blow it with compressed air, check whether the tube is cleaned. When cleaning the tube, be careful not to damage the mouth, inner surface and other machine parts.

The guide wire tube within the second heat box should be cleaned regularly. Turn the hot tank to the tilt state, extract the tube from above, impregnate and heating in a 15% -20% alkali solution, then remove it, washed with hot water, and then blow it with compressed air, and check whether the tube is cleaned. When cleaning the pipe, be careful not to put the tube, inner wall, to avoid damage to the tube to rub the padded rib.

4, the maintenance of the leather roller

First, the two roller roller is usually grinded after 1-3 months, and the San Luoli roller is worn once in 6 months, and the bearing rotation is flexible while polishing.

5, repairing the repair of fake twisters

It is necessary to clear the waste silk wrapped on the ingot and the "snowflake" on the friction plate, and when the grinding disc speed is discovered, the fake tension disorder (confirmed is caused by the abrasive 假), when the head is difficult, should be removed Robbed fake twist check. Check that the small bearing of the fake twist is damaged and the rotation is flexible, and whether the micro-toothed belt that drives three spindles shaft is elongated or worn. If you find an exception to replace it in time.

6, adjustment of the winding device

If the winding key is found to be formed, there is a larger than the outer (detour of the normal trajectory), the collapse, the surface hardness is different, and the winding system must be checked, check whether the winding cartridge beats, whether the trajectory of the traveler is Correctly, etc.

7, check the elastic coupling

Each downtime must check if the elastic coupling of each part is loose or wear, and there is a loose phenomenon that must be tight, if there is wear, it must be replaced.

8, check the synchronization belt

The synchronous belt operation must be checked daily, and it is observed whether there is loose, less teeth, and the synchronous belt mutual friction.

Donghua DHKV1235-12 polyester spinning machinery mainly includes: screw extruder, melt pre-filter, squeezing head, spinning box, biphenyl boiler, metering pump, spinning assembly, side blowing, Oil, ramp, winding machine and electrical control system, etc.

DHKV1235-12 polyester spinning machine

This equipment is mainly used for spinning 50 to 150 darles of polyester Poy filaments, and the product is prefetched towards. Its raw materials are polyester sections. Jiangxi Donghua Machinery Co., Ltd. focuses on the production of polypropylene spinning machine, polypropylene, strong spinning equipment, polypropylene high-strength spinning equipment, polypropylene FDY spinning machine, polyester spinning machine, aramid 1414 fiber spinning equipment, DHP419 series high strength polypropylene Spinning Drawing Machine, Polypropylene Spinning Machine, DHP418 Series Polypropylene Spinning Drawing Machine, DHKV1235-12 Polyester Spinning Machine, DHPE Type High Mode Polyethylene Fiber Spinning Equipment, DHTA Araminated 1414 Fiber Spinning Equipment, HDZF3 High vacuum dynamic drying - solid phase increase stick, polypropylene spinning machine.: